KVH Industries TracVision 6 User Manual Page 60
- Page / 88
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
6. Connect the new antenna gyro’s Molex connector
to the main PCB.
7. Replace the antenna gyro gasket (see Figure 4-6).
8. Using the standoffs removed in Step 3, secure the
new antenna gyro to the bracket. The antenna gyro
should be oriented so that the cable extends from
the top of the gyro, as shown in Figure 4-6.
9. Using a tie-wrap, secure the antenna gyro cable to
the bottom right standoff.
10. Reattach the counterweight, screws, and washers
removed in Step 2.
11. Redress the gyro and RF cables using 3 tie-wraps.
12. Carefully move the reflector through its range of
motion to ensure that the cable moves freely
between the elevation mechanism and the lower
assembly. Adjust the antenna gyro cable as
necessary to ensure proper motion.
13. Reinstall the PCB cover.
Calibrating the Antenna Gyro
1. With a PC connected to the switchplate’s
maintenance port, apply power to the antenna
unit.
2. Type
HALT<cr> (<cr> indicates a carriage
return/ENTER key) while the system is performing
the limit switch initialization routine. The system
will complete the initialization function by finding
the azimuth and elevation switch limits and then
go to the home position.
IMPORTANT! Record the 8-digit serial number
displayed in the startup message.
3. Type
DEBUGON<cr> to enter Debug Mode.
4. Type
CLEAREE<cr>.
5. Type
ZAP<cr> to restart/reinitialize the system.
6. Type
HALT<cr>.
7. Type
DEBUGON<cr>.
8. Type
=TVG6HP<cr>.
Maintenance
54-0166
59
Refer to Section 3.5, “Computer
Diagnostics” on page 47 for
complete details on connecting a
PC to the system via the
maintenance port.
Make sure the cable jacket passes
through the PCB access slot to
protect the wires from the edge of
the PCB frame.
When rotating the antenna by
hand, go slowly! Hitting the
mechanical stops with excessive
force will damage the azimuth limit
switch.
- KVHTracVision 1
- TracVision 6-HP 2
- Technical Manual Addendum 2
- Table of Contents 5
- 1 – Introduction 7
- System Compatibility 8
- In-motion Tracking 8
- Satellite Library 9
- 1.2 TracVision 6 Components 10
- TracVision 6 11
- 2 – Installation 12
- 2.1 Planning the Installation 13
- Kitpack Contents 14
- Choosing Component Locations 15
- Cable Lengths 15
- TracVision Antenna 16
- Vessel Platform 16
- Blocked! 16
- Radar Concerns 17
- Locating the Switchplate 18
- 2.2 Mounting the TracVision 19
- TracVision 6 Technical Manual 20
- Section 4.9, “Preparing for 20
- Shipment” on page 67 20
- 16" 21
- When rotating the azimuth 22
- 2.3 Connecting the IRD(s) 23
- Figure 2-9 24
- Multiswitch 25
- RF Splitters/ 25
- Power Dividers 25
- TracVision Antenna Baseplate 25
- Connecting Three or Four IRDs 26
- Figure 2-11 26
- 2.4 Wiring the Switchplate 27
- Figure 2-13 28
- Figure 2-14 28
- Figure 2-15 29
- 2.5 Mounting the Switchplate 30
- DIRECTV Activation 31
- DISH Network Activation 31
- Other IRD Activations 31
- Programming European IRDs 31
- Programming DSS Plus IRDs 32
- Table 2-6 33
- Table 2-7 33
- Maintenance Port 34
- Installation 35
- SATCONFIG parser command: 36
- Horizontal High 39
- Vertical High 39
- Vertical Low 39
- Horizontal Low 39
- Installing Your Satellites 40
- (European Systems Only) 41
- 2.9 Checking Out the System 42
- 1-year labor warranty 43
- Swap LNBs 44
- Install New Satellites 44
- Replace the IRD 44
- 3 – Troubleshooting 45
- 3.1 Troubleshooting Matrix 46
- Vessel Turning During Startup 47
- Type of Multiswitch Used 49
- 3.5 Computer Diagnostics 50
- 3.6 Maintenance Port Parser 50
- Commands 50
- 4 – Maintenance 51
- 4.2 Preventive Maintenance 52
- 4.3 TracVision 6 Field 53
- Replaceable Units 53
- Removing the PCB Cover 55
- MAIN PCB 56
- Replacing the Main PCB 57
- Replacing the RF PCB 58
- Replacing a Fuse 58
- Assembly 59
- Calibrating the Antenna Gyro 60
- Switch Assembly 62
- Plastic Cam 63
- Black and White Wires 63
- Side View Front View 64
- 4.8 Replacing the LNB 66
- Replacing a European LNB 67
- KVH is not liable for damage 69
- Appendices 70
- Appendix A 71
- System Specifications 71
- Appendix B 72
- Switchplate Template 72
- Appendix C 73
- Comprehensive TracVision 6 73
- Wiring Diagram 73
- Appendix D 74
- Startup Data Sequence 74
- VERSION 76
- STATUS or HELP 76
- E.3 Operational Commands 79
- E.5 RF Board Commands 80
- E.4 Tracking and Conical 80
- Scan Commands 80
- E.6 Installation Commands 84
- E.7 Debug Commands 85
- TV6_TM_Cover.0604 88
Related products and manuals for Satellite antennas KVH Industries TracVision 6
(37 pages)© 2020, manymanuals.com. All rights reserved. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals