KVH Industries TracVision G4 User Manual download pdf (Page 61)

54-0147

TracVision G4 Technical Manual

4. After completing the review of the startup and

operational routines, turn on the IRD and television

and check the channels on the selected satellites.

For European systems, check both horizontally and

vertically polarized channels, if possible.

5. When all checks are completed, shut down the

system.

Be certain to fill out and submit the

warranty card to KVH to ensure

that your TracVision G4 is fully

covered under the 2-year parts and

1-year labor warranty.

1 2 ... 56 57 58 59 60 61 62 63 64 65 66 ... 154 155

KVHTracVision 1
TracVision 2
GyroTrac 3
Table of Contents 6
1 – Introduction 8
System Compatibility 9
In-motion Tracking 9
Satellite Library 10
1.2 TracVision G4 Components 11
TracVision G4 12
2 – Installation 13
2.1 Planning the Installation 14
Kitpack Contents 15
Choosing Component Locations 16
Blocked! 17
TracVision Antenna 17
Vessel Platform 17
Radar Concerns 18
Figure 2-3 20
Foam Seal 21
Single IRD 22
Installation 22
Second IRD 22
When rotating the azimuth 23
Figure 2-9 24
Figure 2-10 24
TOWARD BOW 25
Centerline 27
#8 screw and washer 28
Fabric Strips 29
Hook Disks 29
Option 2 - Flush-mounting 30
2.5 Connecting the IRD(s) 31
(North American Systems only) 32
RF Splitters/ 33
Power Dividers 33
TracVision Antenna Baseplate 33
Multiswitch 33
2.6 Wiring the ADCU 34
Figure 2-21 35
ADCU Wiring 35
Red Label 36
Yellow Label 36
Blue Label 38
(Optional) 39
Green Label 40
Connectors 1 - 36 43
Connectors 60 - 37 43
Yellow Label Red Label 43
Terminal Strip Connector 44
Tie-wrap 44
2.7 Calibrating the Sensor 45
The Calibration Score 46
Other IRD Activations 47
Programming European IRDs 47
Programming DSS Plus IRDs 48
Table 2-9 49
Table 2-10 49
Figure 2-33 50
Figure 2-34 50
Figure 2-35 51
Install Satellite Process 51
Figure 2-36 53
Table 2-12 54
Table 2-11 54
@SAVE,A<cr> (or B if 55
SATINSTALL parser command: 56
Horizontal High 58
Vertical High 58
Vertical Low 58
Horizontal Low 58
(European Systems Only) 59
2.11 Checking Out the System 60
1-year labor warranty 61
Swap LNBs 62
Install New Satellites 62
Replace the IRD 62
3 – Using the ADCU 63
Interface 63
3.1 Startup and Self-test 64
Figure 3-3 65
Figure 3-4 66
Main Menu 67
ARE YOU SURE? 68
** WARNING ** 68
Data will be HALTED 68
Antenna Error Messages 69
3.3 Setup Display Mode 70
3.4 Set Data Outputs Mode 71
Figure 3-11 72
Setting the Serial Outputs 73
Setting the NMEA Outputs 74
Setting the Furuno Output 75
3.5 Set Configuration Mode 76
Values" 77
Entering Gyro Offset Values 78
Choosing the Default Display 79
3.6 Control Compass Mode 80
Reading the Calibration Score 81
Clearing Compass Calibration 81
3.7 Antenna Status Mode 82
Antenna Status Data Screens 83
3.8 Control Antenna Mode 84
Figure 3-28 85
Restarting the Antenna 86
Turning Sleep Mode On/Off 86
Selecting Active Satellite 90
Figure 3-35 92
Satellite Frequency Scan 92
4 – Troubleshooting 93
4.1 Troubleshooting Matrix 94
4.2 Causes and Remedies for 95
Common Operational Issues 95
(North American Systems Only) 97
4.3 GyroTrac-specific Issues 98
4.4 IRD Troubleshooting 99
4.6 Computer Diagnostics 99
4.7 Maintenance Port Parser 100
Commands 100
5 – Maintenance 101
5.2 Preventive Maintenance 102
5.3 TracVision G4 Field 103
Replaceable Units 103
5.4 Replacing the Main PCB 105
Replacing the Main PCB 106
DEBUGON<cr> 107
=TVG4<cr> 107
5.5 Replacing the RF PCB 108
Assembly 110
Calibrating the Antenna Gyro 111
Replacing the Drive Belt 112
5.8 Replacing the LNB 114
Replacing a European LNB 115
5.9 GyroTrac Field 116
5.10 Preparing for Shipment 117
KVH is not liable for damage 118
Appendices 119
Appendix A 120
System Specifications 120
A.2 GyroTrac Compass 121
Specifications 121
Table A-6 122
TracVision G4 GyroTrac 122
Interface Specifications 122
Appendix B 123
TracVision G4 Baseplate 123
Mounting Holes Template 123
Appendix C 125
ADCU Flush Mount 125
Panel Template 125
Appendix D 126
Comprehensive TracVision G4 126
System Wiring Diagram 126
Appendix E 128
Optional Rotating Card 128
FUSE (1A) 129
PACKING GLANDS 129
8 Screws (a) 129
(b) (c) (d) 129
1234567 8 130
Bracket Mounting 132
Panel Mounting 133
Appendix G 136
GyroTrac Data Outputs 136
G.2 Serial Port Outputs 137
Table G-5 139
Cetrek Output 139
Table G-4 139
KVH Output 139
G.3 Furuno Output 140
Figure G-2 141
Converter Wiring Diagram 141
Appendix H 142
Maintenance Port 142
Parser Commands 142
Table H-2 144
H.3 Operational Commands 145
H.4 Tracking and Conical 146
Scan Commands 146
H.5 Sensor Module Commands 146
H.6 RF Board Commands 147
H.7 Installation Commands 151
H.8 Debug Commands 152
KVH Industries, Inc 155
KVH Europe A/S 155

Comments to this Manuals

No comments

KVH Industries TracVision G4 User Manual Page 61

Comments to this Manuals